Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterCGI Door Installation: The Coral Gables Owner’s Guide
CGI door installation in Coral Gables typically runs $1,200 to $2,600 installed, depending on the door width, glass package, and whether the frame gets replaced or just re-set. We stock CGI-compatible hardware and panels at our shop, and most single-door swaps are finished in one day. Most owners don’t discover they need this page until a door starts binding at the top corner in August, or a hinge pulls loose from the jamb after years of salt air working on the fasteners.
CGI doors are built for hurricane zones, which means they’re heavier than standard doors. That weight is the reason installation matters so much. A door that was never shimmed properly, or a hinge that was undersized from day one, wears out the opening faster than anything else. We’ve been called to fix doors that were only five years old but sagged a half inch at the latch because the original installer used interior-grade screws in a coastal application.
Which CGI Models This Applies To
This guide covers the CGI hinged impact door lines most common in Coral Gables: the Estate Collection, the Classic Collection, and the heavier commercial-rated Sentry line that shows up on older Mediterranean homes. Each series uses a different hinge spacing and threshold profile, so the part that fits an Estate door will not always seat correctly on a Sentry door. If you still have the original order paperwork, the product approval number starts with FL and is printed on a sticker near the bottom hinge. If the sticker is gone, measure the door slab thickness with a caliper. CGI doors run 1-3/4 inches on residential models and a full 2 inches on the Sentry line. That quarter inch decides your hinge and threshold options.
We keep OEM CGI hinges, rollers, and thresholds in stock, and we also carry quality aftermarket equivalents from the same Miami-Dade approved suppliers CGI uses. The aftermarket hardware is usually 20 to 30 percent less and performs identically, but if your claim depends on matching the original CGI part number exactly, we quote the OEM line item on paper so there’s no confusion about what’s going on the door. We’re an independent installer, not affiliated with CGI. That means we quote the part that fits your door and budget, not the part a manufacturer rep wants moved this quarter.
Signs Your CGI Door Installation Is Failing
- Door drags or binds at the top latch corner. This is the most common complaint we see in Coral Gables, and it’s almost always a hinge problem. CGI doors are heavy and if the top hinge was shimmed with cardboard or plastic shims instead of steel, the jamb compresses over time and the door rotates forward.
- Water staining or soft drywall below the threshold. Salt air and afternoon downpours find gaps in a threshold that was never bedded in sealant correctly. By the time you see the stain, water has been getting in for months.
- Loose hinge screws or stripped holes in the jamb. A CGI door fastens with screws into the jamb, and if those holes strip out, the door’s weight starts working against the frame. Re-tightening the screws only helps for a few weeks before they pull again.
- Daylight visible between the slab and the weatherstripping. This shows up on older installs where the original weatherstrip was pinched or cut too short. The door still latches, but air, rain, and noise get through.
- Latch or deadbolt that doesn’t align without lifting the handle. This is the classic sign of a sagging slab. The fix is not a new lockset. The fix is re-hanging the door so the frame carries the weight the way it was designed to.
Replacement Cost & What’s Included
A straight same-size CGI door installation in Coral Gables, using your existing frame and slab, runs $1,200 to $1,800. That covers the new hinges, a correctly bedded threshold with sealant, weatherstripping, shimming, and labor. If the frame itself is rotted or out of square past shimming, add $400 to $800 for a replacement frame. If you’re swapping the slab entirely for a new CGI panel, the installed total runs $2,000 to $2,600 depending on glass package and hardware finish.
Our written quote separates parts and labor so you see exactly where the money goes. No change orders later, no surprise line items on the final bill. Every CGI door installation we do includes our Done Right Promise. If the door binds, leaks, or doesn’t latch cleanly after we leave, we come back and fix it. Both manufacturer warranty layers get registered in writing before our truck leaves your driveway. If it is not in writing, it is not a guarantee, it is just a conversation.
DIY or Call Us?
A homeowner with a 4-foot level, a drill, and patience can check hinge screws, re-tighten the threshold, and photograph the product label for us over the phone. Those checks cost nothing and they help us quote the job before we arrive. But the actual re-hanging of a CGI door is not a weekend project. These doors weigh between 180 and 300 pounds depending on the model, and if a slab comes off the hinges while you’re working alone, the result is a cracked tile floor, a bent steel door, or worse. The tension in the frame, the shim sequence, and the threshold seal are not forgiving.
We set and seal these doors every week. We’d rather spend the phone call walking you through the label reading and give you an honest price than read about a door that fell on somebody. Call us at (954) 507-3613 and we’ll tell you what we see from your photos and what the fix costs before we schedule anything.
FAQs
A correctly installed CGI door with proper hinge hardware and sealed threshold should hold up 20 to 25 years in Coral Gables, even with the salt air and afternoon rain. The weak points are the weatherstripping (5 to 7 years) and the hinge screws if they were undersized at the original install. Call (954) 507-3613 if your door is older than 15 years and showing any of the signs above. We’ll give you a straight answer on what’s left in it.
Yes, in most cases. If the slab is sound and the frame hasn’t rotted, re-hanging the door with new hinges, a re-bedded threshold, and fresh weatherstripping fixes the problem for a fraction of replacement cost. If the slab is delaminating or the frame has water damage at the corners, repair stops making sense. We’ll show you the condition before recommending anything.
Most single-door CGI installations in Coral Gables finish in one day, including compounding the hinge screws, setting the threshold, and testing the latch and weatherstrip. If we’re replacing the frame as well, plan for a day and a half. We’ll give you a window and hit it.
We keep OEM CGI hinges, thresholds, and weatherstripping on the truck for the common residential series, along with aftermarket equivalents that meet the same Miami-Dade approval. If you need a full slab with a specific glass package, we order it ahead of the install. Call (954) 507-3613 and a live person will tell you what’s in stock before you schedule anything.
Call TruePane for CGI Door Installation in Coral Gables
We’ve been setting doors in Coral Gables long enough to know which ones hold up and which ones get called back. Dale Kessler grew up around these streets, trained at Miami Dade College reading load specs and product approval numbers, and still won’t leave a job until the door holds plumb and passes a water test. Our technicians show up in uniform, background-checked, and ready to quote your CGI door line by line with no surprises. We’ll be there when we say. Call (954) 507-3613 to schedule your free estimate.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Coral Gables and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.