Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterMr-Glass Roof Repair in Coral Gables: What to Know First
We repair Mr-Glass roof glazing and skylight systems for homeowners across Coral Gables, including Cocoplum, the Biltmore area, and the Granada neighborhoods. Most Mr-Glass roof repairs take one to two visits: the first to diagnose and order the correct parts, the second to remove the failed unit, reset the new one in a proper glazing bed, and water-test the opening with a hose before we pack up. As an independent Mr-Glass service provider, we quote honest pricing on the front end - no change orders, no surprise line items, and no markup games on materials. If a Mr-Glass roof unit is failing in your home, call (954) 507-3613 and ask for a free estimate.
This page is for the Coral Gables homeowner who already knows a roof leak never stays a roof leak. Now it’s water running down a feature wall or staining the ceiling below a second-floor atrium. We’ll walk through how Mr-Glass roof units fail, what repairs actually cost in this market, and why we handle these jobs differently than a general roofer who happens to own a caulk gun.
How Mr-Glass Products Fail - and How We Fix Them
- Weep-channel blockage in curved ridge glazing. Mr-Glass curved and vaulted roof systems used heavily in Coral Gables lanai enclosures and interior courtyards rely on narrow internal weep channels to shed condensation. When those channels clog with pollen, roof grit, or the fine limestone dust that settles on everything in this city, water backs up inside the aluminum frame and shows up as a slow drip on the interior side. We pull the affected cap sections, flush the weeps with a mild solvent matched to the frame finish, and reseal with a UV-stable sealant rated for South Florida’s sun load.
- Original sealant shrinkage along the header bar. On Mr-Glass horizontal ridge beams, the factory-applied sealant under the top cap was often a butyl-based product. Butyl handles a Cleveland winter fine and shrinks badly in Coral Gables heat. We see hairline gaps along the header bar on nearly every original Mr-Glass roof we open up. Hairline is all it takes. We cut out the old bead, solvent-clean the channel, and lay in a marine-grade silicone that stays flexible past twenty-plus years in this climate.
- Clouding inside laminated Mr-Glass lites used for walk-on terraces. Some Coral Gables homes built in the late 1990s and early 2000s spec’d laminated Mr-Glass panels for second-floor walk-on terraces and balcony floors. When moisture creeps in through a nicked edge or a failed perimeter gasket, it shows up as cloudy streaks inside the laminate that you cannot wipe clean from either side. Replacement is the honest answer here. We order the lite cut to size through our glazing suppliers, match the tint and thickness to the original spec, and set it on fresh setting blocks so the replacement does not ride the frame and crack at the edges.
- Stripped or corroded torque screws in low-slope frames. Mr-Glass low-slope roof frames use aluminum torque screws to hold the compression bars that sandwich the glass. After fifteen-plus years in salt air and monsoon-season humidity, those screws seize or strip when a previous repair was done with the wrong driver. We drill out the stripped fastener, re-tap the boss where possible, or install a stainless rivet-nut insert so the compression bar seats evenly. Uneven compression is how replacement glass gets cracked during the install.
- Failed butt-joint gaskets where roof glass meets a vertical wall. The transition point where Mr-Glass roof glazing dies into stucco or a second-story wall is the most common failure point we find. The wedge gasket under the transition flashing shrinks and flattens over time. Water wicks in, runs down the underside of the aluminum, and drips ten feet from the actual opening - which is why the homeowner swears the leak is coming from the middle of the glass when it is not. We remove the old flashing, replace the wedge gasket with an EPDM profile cut to the correct depth, and re-flash with material matched to the wall surface.
Our Mr-Glass Roof Repair Process
Every Mr-Glass roof job in Coral Gables goes through the same sequence, and nothing gets skipped, because skipping steps is how a one-visit repair becomes a five-visit argument.
- 1
Measure and photograph the opening before anything moves. We record the exact panel dimensions, frame condition at all four corners, and any existing water staining. A written record means there is no debate later about whether we caused a problem or found one.
- 2
Identify the true water-entry point. Roof leaks do not always show themselves where they hurt. We run a controlled water test on the dry frame before we open anything, so we know whether the failed component is the sealant, the gasket line, the weeps, or fractured glass near the clamping edge.
- 3
Parts decision: verify OEM availability or source a quality equivalent. Some Mr-Glass extrusion profiles and gasket sets are still available direct through industry supply houses. When they are, we price them into the estimate. When they are not, we source equivalent profiles from our own supplier network and tell you exactly which part we substituted and why. No one gets an aftermarket gasket passed off as factory without knowing it.
- 4
Remove the failed unit or component without damaging the good glass around it. On multi-lite Mr-Glass roofs, the panel next to the failure is often in fine condition. We work each lite free the way you would work a stuck drawer - pressure where it belongs, never on the edge that breaks.
- 5
Reset, reseal, and test. The new or cleaned component goes back in with the correct setting blocks, shims, and sealant. Then we run a water test on the finished opening for a full twenty minutes. If water gets through, the job is not done - that rule is the whole reason the company exists.
- 6
Show you the work and hand you the paperwork. You get a written summary of what we found, what we did, what parts we used, and what our Done Right Promise covers. If it is not in writing, it is not a guarantee - it is just a conversation.
What Mr-Glass Roof Repair Costs in Coral Gables
Mr-Glass roof repair pricing in Coral Gables breaks into a few common scenarios. Each one depends on part availability, ladder or scaffold access, and how long the original sealant takes to cut out cleanly.
- Weep-channel flush and reseal on a small atrium or lanai roof: $380-$650
- Header-bar sealant rebuild on a typical pitched glass roof: $450-$800, more if multiple dormer junctions are involved
- Single custom-cut replacement lite, including setting blocks and new gasket: $700-$1,400 depending on glass type, thickness, and whether it is laminated or tempered
- Full transition-flashing replacement at wall-to-roof joint: $900-$1,800 depending on the stucco patch work involved
- Multiple-panel tear-off and reset for a walk-on terrace: $2,500-$6,000, priced by the panel after we see what is underneath
What moves the price more than anything is deck access. A low-slope Mr-Glass roof we can reach with a ladder is a different day than one that needs scaffolding on the third floor. The material costs are stable. The labor depends on the house. We price the work in writing before we start, and the price on the sheet is the price on the bill. Call (954) 507-3613 and we will come out, put eyes on it, and hand you a real line-item estimate. No charge for the visit.
Why Coral Gables Homeowners Call TruePane Windows & Doors for Mr-Glass Work
We have been setting glass in Coral Gables long enough to know which homes got which Mr-Glass product and which openings are going to fail first. Dale Kessler grew up in this area, spent summers near the Miracle Mile watching his father re-glaze storefronts, and trained in building construction technology at Miami Dade College, where he learned to read load specs and Miami-Dade product-approval numbers the way most people read a menu. So when we quote a Mr-Glass roof repair, the number comes from experience with the actual frames and glass, not from a parts catalog guess.
We stand behind the work with a Done Right Promise, and we answer the phone with a live person at every hour. If a Mr-Glass roof repair is beyond saving and your home would be better served with a new PGT, CGI, CWS, or ES Windows roof system, we will tell you that plainly and price both options side by side on paper. We do not push replacement when a repair will hold, and we do not patch a roof that needs replacement just to book the easy job.
FAQs
Yes, many original Mr-Glass extrusion profiles, compression bars, and gasket sets are still available through our supply network, though some discontinued lines require a sourced equivalent. We tell you exactly what is OEM and what is not before we order anything, and the estimate lists it in writing. Call (954) 507-3613 with your roof details and we can check availability while you are on the phone.
Most original Mr-Glass roof installations on Coral Gables homes are well past their original warranty window, and roof glazing warranties typically covered glass seal failure rather than perimeter sealant or gasket breakdown. We inspect the failed component and give you a honest read on whether any warranty is worth pursuing before recommending paid work. If you want us to document the failure for a claim, we will - photographs, measurements, and a written summary included.
Small sealant and weep-channel repairs are often completed the same week we diagnose them. A custom-cut replacement lite takes longer, typically one to two weeks depending on glass type and whether it needs Miami-Dade product approval paperwork filed. We keep you informed on a real timeline, not an optimistic one. Call (954) 507-3613 and we will tell you what is realistic for your specific opening.
If the frame is square, the weeps are clear, and the failure is a gasket or sealant line, repair is usually the smarter money. If the aluminum is corroded through at the corners or multiple lites are clouding inside, replacement starts making sense. We price both paths and let you decide with real numbers in front of you. No pressure, no scare tactics, just measured facts.
For most repair work on existing openings, Coral Gables does not require a separate building permit, though we always check the current code requirements for the scope before we start. When structural work or new openings are involved, we handle the permit package and inspections. The rule is simple: the work gets done to code, and if a permit is required, it is pulled.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Coral Gables and nearby areas.
If you own a home in Coral Gables with a Mr-Glass roof that is leaking, fogging, or showing signs of seal failure, call (954) 507-3613 today. Our team will schedule a free estimate, inspect the system, and walk you through your repair options with plain pricing and a written quote before any work begins.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.