Mr-Glass Roof Replacement & Installation Nationwide | TruePane Windows & Doors

Mr-Glass Roof Replacement & Installation in Coral Gables: What to Know First

We handle Mr-Glass roof replacement and installation for homeowners across Coral Gables, from the Moorish-style homes near the Biltmore to the mid-century ranches off Old Cutler Road. Most Mr-Glass roof glazing jobs in this area take one to three days depending on panel size and framing condition, and the work is priced as a square deal: a written line-item quote before we begin, no surprise charges when the bill comes. If you own a Mr-Glass roof system that’s leaking, clouding, or showing stress fractures, call (954) 507-3613 and we’ll schedule a free estimate.

Call (954) 507-3613

This page is for Coral Gables homeowners who already have Mr-Glass roof glazing or skylights and want an honest read on whether to repair or replace. We are an independent Mr-Glass service provider, not a factory-authorized dealer, which means we answer to you and the work, not a quota. Every quote comes from Dale Kessler and a team that measures twice before a single panel is ordered.

Key Takeaways

• We service Mr-Glass roof systems throughout Coral Gables, including SunRoom, SkyView, and older ClearSpan series.
• Free estimates, written line-item quotes, and no change orders unless you approve them in writing first.
• Both warranty layers registered in writing before the job is done, per The Keystone Standard.
• Done Right Promise: if it leaks, fogs, or shifts after we leave, we make it right.
• We also service PGT, CGI, CWS, and ES Windows roof glazing when a full system swap makes more sense.

How Mr-Glass Products Fail - and How We Fix Them

Mr-Glass roof systems are not all built the same. What fails on a SunRoom panel in the salt air off Gables-by-the-Sea is not what fails on an older ClearSpan under the oak canopy near Matheson Hammock. Here is what we find most often when we walk a Coral Gables roof.

• SunRoom series gasket compression set. The factory gaskets on SunRoom roof panels were spec’d for a cooler climate. After ten or more South Florida summers, the rubber compresses to half its original thickness and water finds the seam. We replace the gaskets with a higher-durometer EPDM rated for continuous heat exposure, then re-torque the compression bars to the panel manufacturer’s spec. A Mr-Glass owner’s manual will not tell you the original torque values; we keep them on file from years of field measurements.
• SkyView series drainage-channel clogging in the rafter pocket. SkyView panels drain through internal channels that run the length of each rafter. In Coral Gables, live oak litter, mulch dust, and construction grit from nearby remodels work their way into those channels and stop water from escaping. The panel looks fine from below, but water pools at the low end and eventually wicks into the ceiling. We clear the channels, test with a metered water flow, and install a small debris screen at each outlet so it does not return next leaf season.
• ClearSpan series thermal stress cracking on the north edge. The older ClearSpan panels were installed in long runs with rigid glazing stops. On a Coral Gables afternoon, the sun heats the southern half of a panel while the northern edge sits in shade under an overhang or chimney chase. The differential expansion is enough to crack the glass at the stop. We cut replacement panels with a slightly wider expansion allowance and float the glazing stops so the glass can move without binding. This is a fix Mr-Glass factory documentation does not cover, because it is specific to install practices in hot, humid climates.
• Condensation-in-glass (fogging) on dual-pane Mr-Glass roof lights over pools and lanais. Any dual-pane roof glass near a pool deck breathes chlorine-heavy air. The edge seals of Mr-Glass units from the mid-2000s were butyl-based, and butyl gives up in the presence of chloramines. When the seal fails, the glass fogs between panes. We replace the sealed units, respec the edge seal to a silicone-based system, and register the new unit’s warranty in writing before we leave. If you have an older unit that is fogged, calling early is cheaper than replacing rotted rafter ends later.
• Improperly flashed curb mounts on Mr-Glass low-profile skylights. Many Mr-Glass curbs along Coral Gables rooflines were set with a single layer of self-adhered membrane and nothing else. Florida’s afternoon downpours overwhelm that in three to five years. We strip the curb, install a two-layer flashing system with a metal counterflashing cap, and tie it into the roofing underlayment so water sheds the way it should. If the roof substrate is soft, we say so and schedule the carpentry repair in the same visit.

Our Mr-Glass Roof Replacement & Installation Process

Every Mr-Glass roof job in Coral Gables follows the same progression, whether it is one skylight over a bathroom or a full sunroom roof rebuild.

1. 1
   The site walk. One of our background-checked technicians measures every opening twice, checks the condition of the glazing frame and roof deck, and photographs what is there before anything moves.
2. 2
   The parts decision. We identify the Mr-Glass series and determine which components are still available from the manufacturer. Where factory parts are discontinued or the lead time is unreasonable, we quote a quality aftermarket equivalent side by side on paper so you see exactly what you are buying and why.
3. 3
   The written quote. You receive a line-item price covering material, labor, disposal, and any roof-repair work needed. The price on the paper is the price on the bill.
4. 4
   The replacement or installation. We set the new Mr-Glass panels or replacement glass to the manufacturer’s install spec, re-seal with a sealant rated for South Florida UV and humidity, and re-flash the curb or rafter connection as the conditions require.
5. 5
   The water test. We run a metered water test over every seam and joint before we clean up. If water gets through, the job is not done.
6. 6
   The register and the walkthrough. We register both manufacturer warranty layers in writing, walk you through what was done, and leave the job what we call done right. You get the Done Right Promise in writing with the invoice.

What Mr-Glass Roof Replacement & Installation Costs in Coral Gables

Mr-Glass roof work in Coral Gables is priced by the opening, the panel size, and the condition of the framing under it. These are the ranges we quote most often on this side of Miami-Dade County.

• Single skylight glass replacement (typical 2×4 foot unit): $620 to $1,050 installed, depending on whether it is single-pane or dual-pane and whether the curb needs re-flashing.
• Full SunRoom roof panel replacement (per 4×8 foot panel): $840 to $1,380 per panel, including new gaskets, hardware, and water test. Most SunRoom roofs run six to twelve panels.
• ClearSpan thermal crack repair (one panel): $480 to $890, including the wider expansion allowance cut and floating stop modification.
• Fogged dual-pane Mr-Glass roof light replacement (pool or lanai): $720 to $1,225, depending on glass size and whether the frame can be reused.
• Full Mr-Glass roof system replacement with reframing (typical Coral Gables sunroom): $9,000 to $22,000, depending on square footage, accessibility, and whether the existing rafters meet current Miami-Dade load requirements.

The biggest variable is roof deck condition. In Coral Gables, we routinely open a curb and find rotted plywood or termite-damaged rafters that were not visible from below. We photograph it, show you, and quote the repair as a line item before proceeding. You approve it or you do not, but you will never find out about it on the final bill.

Call (954) 507-3613 for a free estimate, and we will put a real number in writing.

Why Coral Gables Homeowners Call TruePane Windows & Doors for Mr-Glass Work

We have served Coral Gables and the surrounding neighborhoods since 2008 across two generations of glass work. Dale Kessler grew up near the Miracle Mile, watching his father re-glaze storefronts before he was old enough to carry a caulk gun unsupervised. That is the staff this company is built on: local people trained on Miami-Dade product approvals and load specs, not a rotating crew out of a franchise playbook.

Our Mr-Glass work is covered by the Done Right Promise and The Keystone Standard. Both manufacturer warranty layers get registered in writing before the truck leaves your driveway, with the durations stated on paper. If it is not in writing, it is not a guarantee; it is just a conversation. When a Mr-Glass panel is not the right fix, we quote PGT, CGI, CWS, or ES Windows alternatives side by side. A live person answers the phone 24 hours a day, 7 days a week, and we intend to still be in town answering it thirty years from now.

FAQs